Hi there,
I need a power supply for my PDP8F computer.
It is missing.
The PDP8F 19" chassis box came in 3 different depths,
600 mm (PSU front to back)
370 mm (PSU across the back)
300 mm (PSU front to back)
I need the shallow one, the 300 mm PSU front to back.
Do you have one available, or know where I can get one please.
Even if it is dead!
regards
ray
Hello,
I'm an employee with the National radio astronomy observatory here in Socorro New Mexico.
As part of our NGVLA upgrades, we are seeking to get rid of old data tapes from the tape reel days of Computing. These contain things such as the boot loaders, OS, specific collection programs and antenna movement programs.
I personally would hate to see these just wind up in the literal dumpster and would like to see them sent out to a museum or an archiving body that can preserve them and keep them safe as a dynamic part of history.
If anyone is interested or knows someone who would be interested in the VLAs data tape library please let me know.
V/R
Danielle Werts
Front end engineer
VLA Socorro New Mexico
I'll be attending VCF SoCal on February 17-18 in Orange (California) in the
capacity of a presenter (on a panel and a solo presentation).
Is anyone else planning to attend the event?
Sellam
2 units working when properly stored a few years ago. 1 unit, parts unit.
Must take all 3.
Tested successfully only with a PC and a VAX.
Located in Frederick, Maryland, USA
>
>Anyone have a VMEbus system they use at least occasionally? If so, what
>make/model/config?
I still use a couple of PPC VME boards (DY4 / Curtiss Wright 182/183/184, both
Conduction-Cooled and Air-Cooled) to test the tail end of hardware that we are
still shipping (by now EOL and basically NOS).
But it's work, I don't find them interesting.
If someone here has the warm fuzzies for PPC VME, we can talk :-)
W
Hi folks,
I’m working on a vt220 debug/repair and have gotten to the point where I need to trace firmware execution at boot. I’ve managed to dump the proms (close to but slightly different from the versions in Lars’ GitHub) and the 8051 internal rom, and can load and disassemble these with the s51 simulator. I also have an HP 1660 logic analyzer successfully configured and clipped up to capture instruction traces.
I’m about to dive in to commenting the disassembly listings, but figured I’d ping here to see if anybody might have done this already in case I wouldn’t have to start from scratch?
thanks much,
—FritzM.
>I have found that computers are much like motorcycles: many of the
>most interesting were never available in the US.
Computers are much like motorcycles: many of the most interesting
ones were TERRIBLE!
W
I don't even have an APC anymore. But since this thing is eyeing me menacingly I figured I'd put the request out. Butler Flats Associates dual external 5 1/4" accoutrement, has it's own controller card (based on wd1771/1772 iirc). Contact me off list if you have these. Much appreciated.
Sent with [Proton Mail](https://proton.me/) secure email.
A quick note on ADM3a screen rot... my vintage collection resides in a cool
(60-72 degrees F) dry basement. My "pride and joy" ADM3a (I have several)
was just starting to show a few bubbles at the corners last September. I
was pulling out some parts units on Friday and noticed that one had a much
better screen than I remembered. Thinking that I might swap screens, I took
a close look at "PnJ" and discovered to my horror that most of the lower
half of the screen had "melted". "PnJ" was on a shelf, below eye level,
nowhere near a vent or other source of heat. I was so annoyed that I
immediately started cleaning/repair without taking any pictures (sorry).
Fortunately, there does not appear to be any corrosion from the "goo". I
completely desoldered and removed the keyboard assembly to get all of the
crud out of (and out from under) it. The mainboard is a fully socketed
example and the crud is down in several of the sockets. I'm still working
on that. Anyway, the take away is don't assume (like I did) that the ruined
ADM3as you see are the result of temperature extremes. It can happen
anywhere. Keep a close eye on yours if you have one.
Bill S.
--
This email has been checked for viruses by Avast antivirus software.
www.avast.com
