I'd like to get an ISA based transputer card. Something with multiple
cpus (so not the B004).
A B008 or one of the clones that accepts multiple TRAM modules would be
ideal (https://www.geekdot.com/inmos-b008)
It doesn't have to be TRAM. I saw this multi-cpu board on ebay.ie but a)
it's more than I was hoping to spend b) I can't find any info on it.
Whatever I get I want there to be reasonable docs and archived
software: https://www.ebay.ie/itm/234283597489
Suggestions on what to look for welcomed. I'm in no rush and good things
come to those who wait. I'm in the USA but have family in the UK and go
there often so I'm looking on ebay.co.uk
Thanks!
Hello all,
as it will be soon of importance to us, I am seeking for the systems
engineering manual and drawings, well, everything about the IBM 727 tape
drive (not the 729!). I especially need the module locations charts and
the module schematics.
I see that there is the CE manual on bitsavers. Eventually, the other
manuals are available somewhere, too?
Christian
I have a non-functioning VT100. I think it is failing in the POST during the
RAM check. I don't know for sure because I can't get it to light up the LEDs
on the keyboard, however I used my logic analyser (a HP1630G) to see what
values were written to the UART to send to the keyboard and I see it sends
the values FF then 1, 2, 3, 4 and finally 5. The last value corresponds to
the RAM test so I am fairly confident the RAM test is what is failing.
I have disassembled the VT100 ROM and if I have understood it correctly it
zeroes out the RAM (high address to low) and then for each address (low
address to high) it tries first to read back the zero and then writes 0xAA
to the location and tries to read that back.
I am also confident the 8080 is working OK because I was able to capture an
address trace on the ROM that showed it executing the program as per the
disassembled ROM.
My problem is getting the logic analyser reliably to tell me how each RAM
chip is being addressed and what data is being read or written. I am seeing
strange values for the addresses (sometimes) and I am not sure I have setup
the logic analyser correctly. I have read the datasheet for the 2114 chip
and I am not entirely clear that I have understood it correctly. Here is how
I have set it up:
Trigger on the -ve edge of Chip Select (pin 8)
Capture A9-A0 as the address
Capture WE as an indication of Read or Write
The timing diagrams show the write cycle where the WE signal and CE signal
seem to transition at the same time and the data may be only valid a bit
later then the CS -ve edge. But this may just be me not knowing how to read
the datasheet. Using the +ve edge of CS seems no better.
Is there something I am missing about how to analyse how the RAM chips are
being used?
Thanks
Rob
Not quite computer tech but I figure this is the best place to ask:
Does anyone recognize the display tech that was used on the Concorde's in-cabin display?
Examples:
https://samchui.com/wp-content/uploads/2016/02/CON15.jpghttps://samchui.com/wp-content/uploads/2016/02/CON16.jpg
The display had fully-formed digits and letters, and showed either Mach and Feet, or Temp and MPH. Some pictures show the display in green and others show it in orange - which of course were popular monochrome CRT colors, yet the display looks too "flat" to be a couple CRT's. Those colors were also popular for Electroluminiscent displays which matches the evident "flatness" but I'm not sure I've seen any EL's with fully formed digits like this with no visible segmentation?
I want to guess it was individual digits back-projected - which was a popular control-theater display tech at the end of the 20th century - but I can't rule out, say, really well-done edge-lit character plates. In any event there doesn't seem to be any visible jitter up and down between digits that I might expect with either of those technologies.
The "FEET" display in the above-referenced JPG's shows some artifacts at the left and right edges which might be a clue?
Some pics of the BA Concorde interior had a simple 15-segment and 7-segment green LED display. Don't need help with that one 🙂.
Tim N3QE
I'm looking for someone near Glasnevin near Dublin, Ireland who would be
willing to pick up an item for me and ship it to me State-side. Seller
will not ship.
Thank you in advance.
Sellam
Hi,
I am looking for a CH3s QH50, P/N 63F3825 for a 9221 ES/9000.
A CH1s would also do.
Anyone have an ES/9000 that is a brick because no processor console
that can help me out?
Regards,
Kevin
The recent Ebay auction for the original PDP-8 got my attention because one
of the photos (the processor logic flipchip array) is a nice snapshot for
comparison purposes with the system I am working on.
https://vintagecomputer.net/digital/pdp-8/PDP-8_flip-chips_left.png (mine)
https://vintagecomputer.net/temp/EBAYPDP-8ProcessorFlipchips.jpg
Given my PDP-8 is close to working, I would assume that the Ebay PDP-8
would have a fighting chance, at least as far as the flip chip
configuration goes. This is also a nice confirmation that I more or less
have the flipchips in the right places. There are only a few slight
differences.
Bill
Hi all,
Looking for an original Sun 370-2068, which is a PS2 to Sun keyboard adapter. If anyone has one please DM me, happy to pay a reasonable price & international shipping if needed.
Thanks!
