DEC RF30 Integrated Storage Element Service Guide

Rob Jarratt robert.jarratt at ntlworld.com
Thu Dec 23 11:46:26 CST 2021


I have tried three different RF30 disks, two of them from one source and one
from a completely different source, so completely different histories. They
all give me the same diagnostic error code, 0x300B, which seems to be too
much of a coincidence, so I think it may be something in my configuration.

I am using a MicroVAX 3800 (KA655 with KFQSA). When I power on, the fault
light comes on and then goes out after a while. This I believe is normal
behaviour. However, as soon as I try to access the disk (e.g. SHOW DEVICES
in the console firmware) the fault light come on and when I boot to VMS
(from a different disk), VMS can't see the drive.

I thought it might be some kind of DSSI ID conflict because I have an RF72
in the machine at ID 0. Removing the RF72 does not change the behaviour.
Installing an ID=0 plug on the RF30 does not change the behaviour. I set the
DIP switches on the RF30s to have an ID=1 and still it doesn't work and
PARAMS reports UNITNUM=0. I followed this page
http://mcmanis.com/chuck/computers/vaxen/dssi-plug.html but it didn't work:

PARAMS> sho /mscp

Parameter     Current           Default        Type     Radix
--------- ----------------  ----------------  --------  -----
MSCPNVR   2020202020202020  2020202020202020
          2020202020202020  2020202020202020
          2020202020202020  2020202020202020
          2020202020202020  2020202020202020    String    Hex   RO
UNITID    1502401193918703     0000000000000  Quadword    Hex   RO
ALLCLASS                 0                 0      Byte    Dec   B
MEDIAID           2264601E          2264601E  Longword    Hex   RO   U
UNITNUM                  0                 0      Word    Dec   U
FIVEDIME                 1                 1   Boolean    0/1   B
FORCEUNI                 1                 1   Boolean    0/1   U
FORCECID                 1                 1   Boolean    0/1   RO
CNT_TMO                 60                60      Word    Dec   RO

PARAMS> set unitnum 1

PARAMS> set forceuni 0

PARAMS> write
Failed to acquire unit, cannot WRITE

Am I doing something wrong?

Thanks

Rob

> -----Original Message-----
> From: cctalk <cctalk-bounces at classiccmp.org> On Behalf Of Rob Jarratt via
> cctalk
> Sent: 23 December 2021 09:45
> To: 'General Discussion: On-Topic and Off-Topic Posts'
> <cctalk at classiccmp.org>
> Subject: RE: DEC RF30 Integrated Storage Element Service Guide
> 
> I wonder if anyone knows what diagnostic code 300B means?
> 
> >>>set host/dup/uqssp/disk 2 params
> PARAMS> status config
> 
> Configuration:
>   Node DIA0   is an RF30 controller
>   Software RFX V103 built on  5-MAY-1989 13:18:42
>   Electronics module name is EN94019334
>   Unit is inoperative, error code 300B(X)
>   Last known unit failure code 300B(X)
>   In 60233 power-on hours, power has cycled 189 times
>   System time is  5-MAY-1989 13:19:46
> 
> Regards
> 
> Rob
> 
> > -----Original Message-----
> > From: cctalk <cctalk-bounces at classiccmp.org> On Behalf Of Rob Jarratt
> > via cctalk
> > Sent: 22 December 2021 15:59
> > To: General Discussion: On-Topic and Off-Topic Posts
> > <cctalk at classiccmp.org>
> > Subject: DEC RF30 Integrated Storage Element Service Guide
> >
> > I am looking for the service guide for the RF30 DSSI disk. It is not
> > on
> Manx and
> > not on BitSavers. Does anyone know of a copy? The part number is
> > apparently EK-RF30D-SV.
> >
> >
> >
> > Thanks
> >
> >
> >
> > Rob



More information about the cctech mailing list