Probs w. M3119 CXY08 MUX on VAX VMS 7.3
Holm Tiffe
holm at freibergnet.de
Tue Aug 18 08:57:12 CDT 2015
Holm Tiffe wrote:
> Holm Tiffe wrote:
>
> > Johnny Billquist wrote:
> >
> > > On 2015-08-18 11:31, Holm Tiffe wrote:
> > > >Jerry Weiss wrote:
> > > >
> > > >>Sorry if some of the suggestions aren?t appropriate, was just throwing a
> > > >>few things out.
> > > >>
> > > >>
> > > >>$analyze/error/since=today/full/include=tx
> > > >>
> > > >>Can you post a sample of the output for one of the lines that has an
> > > >>error?
> > > >>
> > > >>Regards,
> > > >>Jerry
> > > >>
> > > >
> > > >Hmm...
> > > >
> > > >
> > > >$analyze/error/since=yesterday/full/include=tx
> > > >Error Log Report Generator Version V7.1
> > > >%ERF-F-INVQUAVA1, value 'TX' invalid for /INCLUDE qualifier
> > > >$
> > > >
> > > >I've looked over what was reported with $analyze/error/since=yesterday/full
> > > >but haven't found anything interesting ..
> > >
> > > Not sure why /include=tx was suggested. I don't think that makes sense.
> > > Anyway, you found a way around that. Otherwise, the device name should
> > > be used, which should have been TT I believe.
> > >
> > > But I would expect there to be some information in the error log as your
> > > error count is non-zero. Strange...
> > >
> > > Things that would be interesting to check more is that you really have
> > > the right device type and driver installed.
> > >
> > > Johnny
> >
> > I've pulled the card in the meantime and looked at the Qbus connectors
> > from the backplane using a lamp..they are looking nice (there lives a
> > really tiny spider in there, but I dont' think that it would hurt something
> > :-) No way to pull it out w/o dismantling the machine).
> > Now I have connected 5 Volts to the xtal oscillator at the pcb, unfortunately
> > it is ok also, 4,5Vss and the frequency is correct.
> > Now I'm resoldering the PLCC housed gate array on the board with hotair, but
> > I don't think that it would change anything, the soldering points are
> > looking good so far.
> >
> > :-(
> >
> > after that I will retest the board and looking again to the error log.
> > Please be patient..
> >
>
>
> ..ok, nothing has changed (as expected) :-(
>
>
> The additional VT420 is connected to txa3: and I haven't changed the term
> parameters since reboot:
>
> $ sh term txa3:
> Terminal: _TXA3: Device_Type: Unknown Owner: No Owner
>
> Input: 9600 LFfill: 0 Width: 80 Parity: None
> Output: 9600 CRfill: 0 Page: 24
>
> Terminal Characteristics:
> Interactive Echo Type_ahead No Escape
> No Hostsync TTsync Lowercase No Tab
> Wrap Scope No Remote No Eightbit
> Broadcast No Readsync No Form Fulldup
> No Modem No Local_echo Autobaud No Hangup
> No Brdcstmbx No DMA No Altypeahd Set_speed
> No Commsync Line Editing Overstrike editing No Fallback
> No Dialup No Secure server No Disconnect No Pasthru
> No Syspassword No SIXEL Graphics No Soft Characters No Printer Port
> Numeric Keypad No ANSI_CRT No Regis No Block_mode
> No Advanced_video No Edit_mode No DEC_CRT No DEC_CRT2
> No DEC_CRT3 No DEC_CRT4 No DEC_CRT5 No Ansi_Color
> VMS Style Input
> $
>
> I've tried 5 times to copy systartup_vms.com to txa3: since reboot:
>
> $ copy SYSTARTUP_VMS.COM txa3:
> %COPY-E-WRITEERR, error writing TXA3:[]SYSTARTUP_VMS.COM;5
> -RMS-F-WER, file write error
> -SYSTEM-F-TIMEOUT, device timeout
> %COPY-W-NOTCMPLT, SYS$COMMON:[SYSMGR]SYSTARTUP_VMS.COM;5 not completely
> copied
> $
>
> sh dev counts 5 errors for the tty line:
>
> Device Device Error
> Name Status Count
> FTA0: Offline 0
> OPA0: Online 0
> TNA0: Offline 0
> TNA2: Online 0
> TXA0: Online 0
> TXA1: Online 0
> TXA2: Online 0
> TXA3: Online 5
> TXA4: Online 0
> TXA5: Online 0
> TXA6: Online 0
> TXA7: Online 0
> VTA0: Offline 0
>
> But I see nothing in the error log regarding this.
>
> Here comes the error log from analyze/error/since=today/full/output=huf
>
> -------------------------------------------------------------------------
>
> ******************************* ENTRY 472. *******************************
> ERROR SEQUENCE 130. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 11:12:31.08 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:00:20
> SCS NODE: V4300 VAX/VMS V7.3
>
> SYSTEM START-UP KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> TIME OF DAY CLOCK 862C0023
> ******************************* ENTRY 473. *******************************
> ERROR SEQUENCE 131. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 11:12:32.19 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:00:21
> SCS NODE: V4300 VAX/VMS V7.3
>
> MOUNT VOLUME KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> UNIT _DISK0$DIA0:, VOLUME LABEL "OVMSVAXSYS"
>
> 689. QIO OPERATIONS THIS UNIT, 0. ERRORS THIS UNIT
>
> V A X / V M S SYSTEM ERROR REPORT COMPILED 18-AUG-2015 14:12:59
> PAGE 1.
>
> ******************************* ENTRY 474. *******************************
> ERROR SEQUENCE 132. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 11:12:54.76 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:00:44
> SCS NODE: V4300 VAX/VMS V7.3
>
> DEVICE ATTENTION KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> "DSA" PORT SUB-SYSTEM, UNIT _V4300$PUA0:, INIT SEQUENCE COMPLETED
>
> SA 40D6
> CONTROLLER MICRO-CODE #6.
> PORT IS KDA50Q
> STEP 4
>
> INIT SEQUENCE
>
> UCB$W_PORTSTEP1 0B00
> ENHANCED DIAGNOSTICS IMPLEMENTED
> 22-BIT HOST ADDRESSING SUPPORTED
> STEP 1
> UCB$W_HOSTSTEP1 A49B
> INTERRUPT VECTOR 000154(OCTAL)
> INTERRUPT ENABLE
> 16. RING RESPONSE SLOTS
> 16. COMMAND RING SLOTS
> UCB$W_PORTSTEP2 10A4
> 16. RING RESPONSE SLOTS
> 16. COMMAND RING SLOTS
> STEP 2
> UCB$W_HOSTSTEP2 C490
> UCB$W_PORTSTEP3 209B
> INTERRUPT VECTOR 000154 (OCTAL)
> INTERRUPT ENABLE
> STEP 3
> UCB$W_HOSTSTEP3 0003
> MAPPING REGISTER #482 SELECTED
> UCB$W_PORTSTEP4 40D6
> CONTROLLER MICRO-CODE #6.
> PORT IS KDA50Q
> STEP 4
> UCB$W_HOSTSTEP4 0403
> GO
> HOST REQUESTS "LAST FAIL"
> CONTROLLER SCRATCHPAD PRESENT
> "BURST" 2. 16-BIT TRANSFER(S)
>
> MAPPING ALLOCATION INFORMATION
>
> VEC$L_MAPREG 000E81E2
> "MPR" #482. STARTING MAP REGISTER
> "MPR"(S) PERMANENTLY ALLOCATED
> 14. MAP REGISTER(S) ALLOCATED
> DIRECT DATAPATH
> ORB$L_OWNER 00010004
> OWNER UIC [001,004]
>
> V A X / V M S SYSTEM ERROR REPORT COMPILED 18-AUG-2015 14:12:59
> PAGE 2.
>
> UCB$L_CHAR 0C450000
> SHARABLE
> AVAILABLE
> ERROR LOGGING
> CAPABLE OF INPUT
> CAPABLE OF OUTPUT
> UCB$W_STS 0000
> UCB$L_OPCNT 00000000
> 0. QIO'S THIS UNIT
> UCB$W_ERRCNT 0001
> 1. ERRORS THIS UNIT
> UCB$W_NUMBINITS 0001
> 1. INIT SEQUENCE
>
> V A X / V M S SYSTEM ERROR REPORT COMPILED 18-AUG-2015 14:13:00
> PAGE 3.
>
> ******************************* ENTRY 475. *******************************
> ERROR SEQUENCE 133. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 11:12:54.77 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:00:44
> SCS NODE: V4300 VAX/VMS V7.3
>
> DEVICE ATTENTION KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> "DSA" PORT SUB-SYSTEM, UNIT _V4300$PTB0:, INIT SEQUENCE COMPLETED
>
> SA 4034
> CONTROLLER MICRO-CODE #4.
> PORT IS TK50P
> STEP 4
>
> INIT SEQUENCE
>
> UCB$W_PORTSTEP1 0BC0
> PORT SUPPORTS ADDRESS MAPPING
> PORT ALLOWS HOST ODD ADDRESSES
> ENHANCED DIAGNOSTICS IMPLEMENTED
> 22-BIT HOST ADDRESSING SUPPORTED
> STEP 1
> UCB$W_HOSTSTEP1 A4B0
> INTERRUPT VECTOR 000300(OCTAL)
> INTERRUPT ENABLE
> 16. RING RESPONSE SLOTS
> 16. COMMAND RING SLOTS
> UCB$W_PORTSTEP2 10A4
> 16. RING RESPONSE SLOTS
> 16. COMMAND RING SLOTS
> STEP 2
> UCB$W_HOSTSTEP2 8C90
> UCB$W_PORTSTEP3 20B0
> INTERRUPT VECTOR 000300 (OCTAL)
> INTERRUPT ENABLE
> STEP 3
> UCB$W_HOSTSTEP3 0003
> MAPPING REGISTER #70 SELECTED
> UCB$W_PORTSTEP4 4034
> CONTROLLER MICRO-CODE #4.
> PORT IS TK50P
> STEP 4
> UCB$W_HOSTSTEP4 0403
> GO
> HOST REQUESTS "LAST FAIL"
> CONTROLLER SCRATCHPAD PRESENT
> "BURST" 2. 16-BIT TRANSFER(S)
>
> MAPPING ALLOCATION INFORMATION
>
> VEC$L_MAPREG 000E81C6
> "MPR" #454. STARTING MAP REGISTER
> "MPR"(S) PERMANENTLY ALLOCATED
> 14. MAP REGISTER(S) ALLOCATED
> DIRECT DATAPATH
>
> V A X / V M S SYSTEM ERROR REPORT COMPILED 18-AUG-2015 14:13:00
> PAGE 4.
>
> ORB$L_OWNER 00010004
> OWNER UIC [001,004]
> UCB$L_CHAR 0C450000
> SHARABLE
> AVAILABLE
> ERROR LOGGING
> CAPABLE OF INPUT
> CAPABLE OF OUTPUT
> UCB$W_STS 0000
> UCB$L_OPCNT 00000000
> 0. QIO'S THIS UNIT
> UCB$W_ERRCNT 0001
> 1. ERRORS THIS UNIT
> UCB$W_NUMBINITS 0001
> 1. INIT SEQUENCE
>
> V A X / V M S SYSTEM ERROR REPORT COMPILED 18-AUG-2015 14:13:00
> PAGE 5.
>
> ******************************* ENTRY 476. *******************************
> ERROR SEQUENCE 134. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 11:12:54.77 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:00:44
> SCS NODE: V4300 VAX/VMS V7.3
>
> ERL$LOGMESSAGE KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> "DSA" PORT SUB-SYSTEM, UNIT _V4300$PUA0:
>
> MESSAGE TYPE 0004
> UDA PORT MESSAGE
> MSLG$L_CMD_REF 00000000
> MSLG$W_SEQ_NUM 0000
> SEQUENCE #0.
> MSLG$B_FORMAT 00
> CONTROLLER LOG
> MSLG$B_FLAGS 01
> SEQUENCE NUMBER RESET
> UNRECOVERABLE ERROR
> MSLG$W_EVENT 0010
> RECORD DATA TRUNCATED
> MSLG$Q_CNT_ID 00D60000
> 01020000
> UNIQUE IDENTIFIER, 000000D60000(X)
> MASS STORAGE CONTROLLER
> UDA50
> MSLG$B_CNT_SVR D6
> CONTROLLER SOFTWARE VERSION #214.
> MSLG$B_CNT_HVR 04
> CONTROLLER HARDWARE REVISION #4.
>
> V A X / V M S SYSTEM ERROR REPORT COMPILED 18-AUG-2015 14:13:00
> PAGE 6.
>
> ******************************* ENTRY 477. *******************************
> ERROR SEQUENCE 135. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 11:12:54.84 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:00:44
> SCS NODE: V4300 VAX/VMS V7.3
>
> DEVICE ATTENTION KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> TK70P SUB-SYSTEM, V4300$PTA0:
>
> FAILED TO LOCATE PORT MICRO-CODE IMAGE
> ******************************* ENTRY 478. *******************************
> ERROR SEQUENCE 136. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 11:14:04.39 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:01:53
> SCS NODE: V4300 VAX/VMS V7.3
>
> MOUNT VOLUME KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> UNIT _DISK2$DIA2:, VOLUME LABEL "DATA2"
>
> 12. QIO OPERATIONS THIS UNIT, 0. ERRORS THIS UNIT
> ******************************* ENTRY 479. *******************************
> ERROR SEQUENCE 137. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 11:23:02.82 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:10:52
> SCS NODE: V4300 VAX/VMS V7.3
>
> TIME STAMP KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
> ******************************* ENTRY 480. *******************************
> ERROR SEQUENCE 138. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 11:30:48.62 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:18:37
> SCS NODE: V4300 VAX/VMS V7.3
>
> DISMOUNT VOLUME KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> UNIT _DISK2$DIA2:, VOLUME LABEL "DATA2"
>
> 17. QIO OPERATIONS THIS UNIT, 0. ERRORS THIS UNIT
> 5. QIO OPERATIONS THIS VOLUME, 0. ERRORS THIS VOLUME
>
> V A X / V M S SYSTEM ERROR REPORT COMPILED 18-AUG-2015 14:13:00
> PAGE 7.
>
> ******************************* ENTRY 481. *******************************
> ERROR SEQUENCE 139. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 11:30:58.08 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:18:47
> SCS NODE: V4300 VAX/VMS V7.3
>
> FATAL BUGCHECK KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> OPERATOR, Operator requested system shutdown
> ******************************* ENTRY 482. *******************************
> ERROR SEQUENCE 140. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 13:43:24.27 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:00:20
> SCS NODE: V4300 VAX/VMS V7.3
>
> SYSTEM START-UP KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> TIME OF DAY CLOCK 8639D08A
> ******************************* ENTRY 483. *******************************
> ERROR SEQUENCE 141. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 13:43:25.39 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:00:21
> SCS NODE: V4300 VAX/VMS V7.3
>
> MOUNT VOLUME KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> UNIT _DISK0$DIA0:, VOLUME LABEL "OVMSVAXSYS"
>
> 689. QIO OPERATIONS THIS UNIT, 0. ERRORS THIS UNIT
>
> V A X / V M S SYSTEM ERROR REPORT COMPILED 18-AUG-2015 14:13:00
> PAGE 8.
>
> ******************************* ENTRY 484. *******************************
> ERROR SEQUENCE 142. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 13:43:48.59 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:00:45
> SCS NODE: V4300 VAX/VMS V7.3
>
> DEVICE ATTENTION KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> "DSA" PORT SUB-SYSTEM, UNIT _V4300$PUA0:, INIT SEQUENCE COMPLETED
>
> SA 40D6
> CONTROLLER MICRO-CODE #6.
> PORT IS KDA50Q
> STEP 4
>
> INIT SEQUENCE
>
> UCB$W_PORTSTEP1 0B00
> ENHANCED DIAGNOSTICS IMPLEMENTED
> 22-BIT HOST ADDRESSING SUPPORTED
> STEP 1
> UCB$W_HOSTSTEP1 A49B
> INTERRUPT VECTOR 000154(OCTAL)
> INTERRUPT ENABLE
> 16. RING RESPONSE SLOTS
> 16. COMMAND RING SLOTS
> UCB$W_PORTSTEP2 10A4
> 16. RING RESPONSE SLOTS
> 16. COMMAND RING SLOTS
> STEP 2
> UCB$W_HOSTSTEP2 C450
> UCB$W_PORTSTEP3 209B
> INTERRUPT VECTOR 000154 (OCTAL)
> INTERRUPT ENABLE
> STEP 3
> UCB$W_HOSTSTEP3 0003
> MAPPING REGISTER #482 SELECTED
> UCB$W_PORTSTEP4 40D6
> CONTROLLER MICRO-CODE #6.
> PORT IS KDA50Q
> STEP 4
> UCB$W_HOSTSTEP4 0403
> GO
> HOST REQUESTS "LAST FAIL"
> CONTROLLER SCRATCHPAD PRESENT
> "BURST" 2. 16-BIT TRANSFER(S)
>
> MAPPING ALLOCATION INFORMATION
>
> VEC$L_MAPREG 000E81E2
> "MPR" #482. STARTING MAP REGISTER
> "MPR"(S) PERMANENTLY ALLOCATED
> 14. MAP REGISTER(S) ALLOCATED
> DIRECT DATAPATH
> ORB$L_OWNER 00010004
> OWNER UIC [001,004]
>
> V A X / V M S SYSTEM ERROR REPORT COMPILED 18-AUG-2015 14:13:00
> PAGE 9.
>
> UCB$L_CHAR 0C450000
> SHARABLE
> AVAILABLE
> ERROR LOGGING
> CAPABLE OF INPUT
> CAPABLE OF OUTPUT
> UCB$W_STS 0000
> UCB$L_OPCNT 00000000
> 0. QIO'S THIS UNIT
> UCB$W_ERRCNT 0001
> 1. ERRORS THIS UNIT
> UCB$W_NUMBINITS 0001
> 1. INIT SEQUENCE
>
> V A X / V M S SYSTEM ERROR REPORT COMPILED 18-AUG-2015 14:13:00
> PAGE 10.
>
> ******************************* ENTRY 485. *******************************
> ERROR SEQUENCE 143. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 13:43:48.60 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:00:45
> SCS NODE: V4300 VAX/VMS V7.3
>
> DEVICE ATTENTION KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> "DSA" PORT SUB-SYSTEM, UNIT _V4300$PTB0:, INIT SEQUENCE COMPLETED
>
> SA 4034
> CONTROLLER MICRO-CODE #4.
> PORT IS TK50P
> STEP 4
>
> INIT SEQUENCE
>
> UCB$W_PORTSTEP1 0BC0
> PORT SUPPORTS ADDRESS MAPPING
> PORT ALLOWS HOST ODD ADDRESSES
> ENHANCED DIAGNOSTICS IMPLEMENTED
> 22-BIT HOST ADDRESSING SUPPORTED
> STEP 1
> UCB$W_HOSTSTEP1 A4B0
> INTERRUPT VECTOR 000300(OCTAL)
> INTERRUPT ENABLE
> 16. RING RESPONSE SLOTS
> 16. COMMAND RING SLOTS
> UCB$W_PORTSTEP2 10A4
> 16. RING RESPONSE SLOTS
> 16. COMMAND RING SLOTS
> STEP 2
> UCB$W_HOSTSTEP2 8C50
> UCB$W_PORTSTEP3 20B0
> INTERRUPT VECTOR 000300 (OCTAL)
> INTERRUPT ENABLE
> STEP 3
> UCB$W_HOSTSTEP3 0003
> MAPPING REGISTER #70 SELECTED
> UCB$W_PORTSTEP4 4034
> CONTROLLER MICRO-CODE #4.
> PORT IS TK50P
> STEP 4
> UCB$W_HOSTSTEP4 0403
> GO
> HOST REQUESTS "LAST FAIL"
> CONTROLLER SCRATCHPAD PRESENT
> "BURST" 2. 16-BIT TRANSFER(S)
>
> MAPPING ALLOCATION INFORMATION
>
> VEC$L_MAPREG 000E81C6
> "MPR" #454. STARTING MAP REGISTER
> "MPR"(S) PERMANENTLY ALLOCATED
> 14. MAP REGISTER(S) ALLOCATED
> DIRECT DATAPATH
>
> V A X / V M S SYSTEM ERROR REPORT COMPILED 18-AUG-2015 14:13:00
> PAGE 11.
>
> ORB$L_OWNER 00010004
> OWNER UIC [001,004]
> UCB$L_CHAR 0C450000
> SHARABLE
> AVAILABLE
> ERROR LOGGING
> CAPABLE OF INPUT
> CAPABLE OF OUTPUT
> UCB$W_STS 0000
> UCB$L_OPCNT 00000000
> 0. QIO'S THIS UNIT
> UCB$W_ERRCNT 0001
> 1. ERRORS THIS UNIT
> UCB$W_NUMBINITS 0001
> 1. INIT SEQUENCE
>
> V A X / V M S SYSTEM ERROR REPORT COMPILED 18-AUG-2015 14:13:00
> PAGE 12.
>
> ******************************* ENTRY 486. *******************************
> ERROR SEQUENCE 144. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 13:43:48.60 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:00:45
> SCS NODE: V4300 VAX/VMS V7.3
>
> ERL$LOGMESSAGE KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> "DSA" PORT SUB-SYSTEM, UNIT _V4300$PUA0:
>
> MESSAGE TYPE 0004
> UDA PORT MESSAGE
> MSLG$L_CMD_REF 00000000
> MSLG$W_SEQ_NUM 0000
> SEQUENCE #0.
> MSLG$B_FORMAT 00
> CONTROLLER LOG
> MSLG$B_FLAGS 01
> SEQUENCE NUMBER RESET
> UNRECOVERABLE ERROR
> MSLG$W_EVENT 0010
> RECORD DATA TRUNCATED
> MSLG$Q_CNT_ID 00D60000
> 01020000
> UNIQUE IDENTIFIER, 000000D60000(X)
> MASS STORAGE CONTROLLER
> UDA50
> MSLG$B_CNT_SVR D6
> CONTROLLER SOFTWARE VERSION #214.
> MSLG$B_CNT_HVR 04
> CONTROLLER HARDWARE REVISION #4.
>
> V A X / V M S SYSTEM ERROR REPORT COMPILED 18-AUG-2015 14:13:00
> PAGE 13.
>
> ******************************* ENTRY 487. *******************************
> ERROR SEQUENCE 145. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 13:43:48.67 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:00:45
> SCS NODE: V4300 VAX/VMS V7.3
>
> DEVICE ATTENTION KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> TK70P SUB-SYSTEM, V4300$PTA0:
>
> FAILED TO LOCATE PORT MICRO-CODE IMAGE
> ******************************* ENTRY 488. *******************************
> ERROR SEQUENCE 146. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 13:43:53.42 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:00:49
> SCS NODE: V4300 VAX/VMS V7.3
>
> MOUNT VOLUME KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> UNIT _DISK1$DIA1:, VOLUME LABEL "DATA1"
>
> 12. QIO OPERATIONS THIS UNIT, 0. ERRORS THIS UNIT
> ******************************* ENTRY 489. *******************************
> ERROR SEQUENCE 147. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 13:45:13.75 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:02:10
> SCS NODE: V4300 VAX/VMS V7.3
>
> MOUNT VOLUME KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
>
> UNIT _DISK2$DIA2:, VOLUME LABEL "DATA2"
>
> 12. QIO OPERATIONS THIS UNIT, 0. ERRORS THIS UNIT
> ******************************* ENTRY 490. *******************************
> ERROR SEQUENCE 149. LOGGED ON: SID 0B000006
> DATE/TIME 18-AUG-2015 14:04:12.27 SYS_TYPE 01340401
> SYSTEM UPTIME: 0 DAYS 00:21:08
> SCS NODE: V4300 VAX/VMS V7.3
>
> TIME STAMP KA670-AA CPU FW REV# 6. CONSOLE FW REV# 3.4
> ANALYZE/ERROR/SINCE=18-AUG-2015 00:00:00.00/FULL/OUTPUT=HUF
> -------------------------------------------------------------------------
>
>
> What makes me wonder is that I've wrote that the vector of the card schould
> be 300...but:
>
>
> $ mcr sysgen
> SYSGEN> SH/CONF
>
> System CSR and Vectors on 18-AUG-2015 14:11:12.81
>
> Name: PAA Units: 1 Nexus:0 (CI )
> Name: PAB Units: 1 Nexus:1 (CI )
> Name: EZA Units: 4 Nexus:2 (NI )
> Name: PUA Units: 1 Nexus:3 (UBA) CSR: 772150 Vector1: 154 Vector2: 000
> Name: PTA Units: 1 Nexus:3 (UBA) CSR: 774500 Vector1: 260 Vector2: 000
> Name: PTB Units: 1 Nexus:3 (UBA) CSR: 760404 Vector1: 300 Vector2: 000
> Name: TXA Units: 8 Nexus:3 (UBA) CSR: 760440 Vector1: 310 Vector2: 314
> SYSGEN>
>
> ...floating vector?
>
..tried switchuing the board from the DHU11 Mode to DHV11 and rebooted,
problem is exactly the same...
I'm now out of ideas..other suggestions?
I would search my stock for the DHV-11 compatible Emulex card that I have
and try it in that machine next.
Regards,
Holm
--
Technik Service u. Handel Tiffe, www.tsht.de, Holm Tiffe,
Freiberger Straße 42, 09600 Oberschöna, USt-Id: DE253710583
www.tsht.de, info at tsht.de, Fax +49 3731 74200, Mobil: 0172 8790 741
More information about the cctech
mailing list