DEC top-mount corporate cabinet
pbirkel at gmail.com
pbirkel at gmail.com
Wed Mar 2 02:46:02 CST 2022
Your description sounds like the cabinet has already been hacked by a prior
owner to remove a key component. And you're saying that the rear
cross-piece is present but both of the top cross-pieces are absent?
Completely weird. I'll contact you off-list and we can exchange photos to
determine what's-what.
-----Original Message-----
From: Chris Elmquist <chrise at pobox.com>
Sent: Tuesday, March 1, 2022 5:21 PM
To: pbirkel at gmail.com
Cc: 'General Discussion: On-Topic and Off-Topic Posts'
<cctalk at classiccmp.org>
Subject: Re: DEC top-mount corporate cabinet
Thanks very much Paul and others. The overview you linked is very helpful
as I now have the actual model number for the rack that I have.
It is indeed the H9642-AD 40" "Top Loader" but it is missing whatever cross
piece goes behind the H9544 DA Bezel (#4) shown in the component parts
diagram.
My mystery is what that cross piece behind the bezel looks like, how it
attaches to the vertical rails of the rack on each side and then how the
bezel attaches to the cross piece.
The back of the bezel has a ribbed channel that looks like some kind of
bolts or other threaded or inserted fasteners were screwed or snapped into
this channel and those were attached to the cross piece somehow.
That's my missing link ...
I fabricated an aluminum bar cross piece and then used heavy duty hook and
loop-like fasteners to attach the bezel to this aluminum bar but it's cheesy
and loose. I'd like to someday find the proper solution.
Chris
On Tuesday (03/01/2022 at 03:23AM -0500), pbirkel at gmail.com wrote:
> Chris:
>
> The traditional DEC racks/cabinets are either full-height ("standard"
> =
> H960) and part-height ("short" = H967) 19" racks. These are welded
> steel frames built for computer-room type environments. When DEC
> started selling into office environments (think data processing /
> business operations) they designed a new line of cabinetry that was
> intended to fit into an office where sight-lines are important and the
> desire was to look/work more like other types of office equipment.
> The PDP-11/60 was I think an early example of the redesigned cabinets
> -- really a double-wide plus a bit, but of more modest height (roughly
> that of the H967). After that you see single-width cabinets holding
> just 18U like the one that you have -- capable of holding a complete,
> but modest, system. These newer-style cabinets/racks are riveted,
> rather than welded. Emphasis was on style, cost-effectiveness, and RF
shielding given the need to operate near other types of office equipment.
>
> Here's a good overview:
> http://vtda.org/docs/computing/DEC/Catalogs/EA21388-75_CabinetAccessor
> iesSup
> pliesCatalog1981.pdf
>
> On the left side of page 8-of-16 you'll see a description of the 40"
> Medium Systems Series, including diagrams and pictures of the "top-loader"
> (H9642-AD) and "front-loader" (H9642-CA) designs. There isn't any
"mod-kit"
> to go from one to the other. It would be possible to get a functional
> top-loader out of a front-loader with some metal reworking.
> Basically, remove the lid and then (in effect) move the cross-pieces
> down 6U and add what amount to four gusset plates for lateral bracing.
> In the H9642-AD photo you can see the plates on the rear cross-piece.
> The front is similar, but sensitive to ensuring that the center 6U
> isn't significantly occluded; the front cross-piece may require some
> modification. There are a few other changes but moving the
> cross-pieces down are the key. Notice the H9544 CA Trim Kit,
> RL01/RL02 -- these are plastic pieces that bridge the gap between the
> HDD cover and the cabinet side-panels; nice to have but they're mostly
there for style.
>
> If you decide to attempt (or simply want to gauge the complexity of) a
> conversion I can see about getting some close-up photos of the various
> components and connections. A conversion would not be a simple task.
>
> While the brochure speaks of "purchase as component kits" and the
> table simply states "Basic Frame Kit", it's not the *same* frame kit
> for -AD and -CA, and I suspect that "kit" in this case was not an IKEA
> flat-box of parts but rather a factory-assembled frame to which one
> added other components as appropriate for the intended use. These frames
are _seriously_ riveted.
> Notice that H9542-AD is distinct from the H9542-CA "component kit".
>
> (Note that the TU80 -- http://gunkies.org/w/images/5/52/Tu80.jpg -- is
> basically a H9642-AD "top-loader" with a hinged lid and
> special-purpose 13U
> front.)
--
Chris Elmquist
More information about the cctalk
mailing list