Interesting RK8E fault

Guy Sotomayor Jr ggs at shiresoft.com
Sun Dec 9 00:43:45 CST 2018


> On Dec 8, 2018, at 10:36 PM, Josh Dersch <derschjo at gmail.com> wrote:
> 
> On Sat, Dec 8, 2018 at 10:33 PM Guy Sotomayor Jr <ggs at shiresoft.com <mailto:ggs at shiresoft.com>> wrote:
> 
> > On Dec 8, 2018, at 8:50 PM, Josh Dersch via cctalk <cctalk at classiccmp.org <mailto:cctalk at classiccmp.org>> wrote:
> > 
> > On Sat, Dec 8, 2018 at 7:24 PM Paul Anderson via cctalk <
> > cctalk at classiccmp.org <mailto:cctalk at classiccmp.org>> wrote:
> > 
> >> Are you using the same pack for the 8 and the 11
> >> 
> > 
> > I connected the drive I normally use with my 11/40 to the 8/e for testing
> > to help narrow down where the fault was.
> > I used a 16-sector pack in all cases.
> 
> You should be using 12 sector packs on the 11 and 16 sector packs on the 8.
> 
> I’m actually surprised the 16 sector pack worked on the 11.
> 
> In all cases /pertinent to this discussion/, i.e. with the RK8E attached to both the 11/40's RK05 and the RK05 I've restored for the 8/e. 
> 
> I have 12-sector packs that I normally use with the 11/40.

OK, just so that I understand the problem:

Do you see the problem only on the RK05 you restored for the 8/e and don’t see it on the drives from the 11/40?
Or do you see the problem on all the drives when hooked to the 8/e and when using a 12 sector pack on the 11/40 you don’t see the problem when using any of the drives on the 11/40?
Or do you see the problem on the drive restored for the 8/e but not on the drives from the 11/40?

TTFN - Guy

> 
> 
> > 
> > 
> >> 
> >> On Sat, Dec 8, 2018 at 8:54 AM Bill Degnan via cctalk <
> >> cctalk at classiccmp.org <mailto:cctalk at classiccmp.org>>
> >> wrote:
> >> 
> >>> On Sat, Dec 8, 2018, 1:02 AM Josh Dersch via cctalk <
> >> cctalk at classiccmp.org <mailto:cctalk at classiccmp.org>
> >>> wrote:
> >>> 
> >>>> On Fri, Dec 7, 2018 at 9:58 PM Josh Dersch <derschjo at gmail.com <mailto:derschjo at gmail.com>> wrote:
> >>>> 
> >>>>> Hi all --
> >>>>> 
> >>>>> Finally got all the parts together (and my act together) to actually
> >>> get
> >>>>> an RK05 lashed up to my PDP-8/e -- only took a decade or so :).  I
> >>> fixed
> >>>> a
> >>>>> few problems with the RK05 and it appears to be behaving very nicely.
> >>>>> 
> >>>>> The RK8E controller is mostly working properly but fails
> >> interestingly
> >>>>> when running the formatter, and during the exerciser -- on cylinder
> >> 128
> >>>> and
> >>>>> 192 and very infrequently on cylinder 64 it will get a cylinder
> >>> mismatch
> >>>>> when doing the seek.  When running the formatter during the
> >>> verification
> >>>>> pass, on cyls 64 and 128 if I retry the read it'll continue without
> >>>> issues,
> >>>>> but it's never successful on a retry on cylinder 192.  I tried
> >> hooking
> >>> it
> >>>>> to the RK05 in my 11/40 and it exhibits the same behavior, so I'm
> >>>> guessing
> >>>>> the drive isn't at fault.  And the error is consistent across packs
> >> (of
> >>>>> which I have only two).
> >>>>> 
> >>>>> Apart from that fault the drive and controller seem to work fine -- I
> >>>>> wrote out an OS/8 pack with Adventure on it (or at least the first
> >> 191
> >>>>> cylinders of it) and it works without issue.
> >>>>> 
> >>>>> Reading the RK8E service docs and schematics, the cylinder address
> >>>> compare
> >>>>> is done by reusing the CRC buffer, so I suspect the issue is in or
> >>> around
> >>>>> there -- the big problem is that debugging it is rather painful since
> >>>> that
> >>>>> logic is in the middle board of a three board set, with jumper blocks
> >>> on
> >>>>> top -- so bringing it out on an extender isn't an option.  I'm
> >> curious
> >>> if
> >>>>> anyone's seen this issue or is so very familiar with the logic that
> >> the
> >>>>> fault is obvious.
> >>>>> 
> >>>>> I suspected the 7496 shift register at E14 which takes in the
> >> cylinder
> >>>>> address to be compared w/the header on disk, and I went ahead and
> >>>> replaced
> >>>>> it in the hopes that I'd get lucky, but no go.
> >>>>> 
> >>>>> Anyone have any advice?
> >>>>> 
> >>>>> Thanks,
> >>>>> Josh
> >>>>> 
> >>>>> 
> >>>> I'll add that during the format/verification the drive seeks properly
> >>> (i.e.
> >>>> it's not missing a step or overstepping), which I've confirmed by
> >>> watching
> >>>> the thing walk through the tracks with the cover off.
> >>>> 
> >>>> - Josh
> >>>> 
> >>> 
> >>> Partitions as rka0 / rka1?
> >>> B
> >>> 
> >>>> 
> >>> 
> >> 
> 



More information about the cctalk mailing list