VAX 4000/300 start up / KA670 issues

dave.g4ugm at gmail.com dave.g4ugm at gmail.com
Mon Sep 14 08:07:09 CDT 2020


Aaron,

Which SCSI card do you have? These systems are normally DSSI systems not
SCSI
You should be able to do SHOW DEVICE then BOOT <name>

Dave

> -----Original Message-----
> From: cctalk <cctalk-bounces at classiccmp.org> On Behalf Of Aaron Jackson
via
> cctalk
> Sent: 14 September 2020 13:36
> To: Aaron Jackson <Aaron.Jackson at nottingham.ac.uk>; General Discussion:
On-
> Topic and Off-Topic Posts <cctalk at classiccmp.org>
> Subject: Re: VAX 4000/300 start up / KA670 issues
> 
> On 14 September 2020 at 00:17 BST, Aaron Jackson via cctalk wrote:
> 
> > Hi
> >
> > I've had a VAX 4000/300 sitting around for the past couple of years.
> > The second time I tried to switch it on there was a bit pop from the
> > power supply. The 12v module of the H7874 PSU is completely dead and
> > despite my best efforts I have not been able to fix it.
> >
> > Tonight I decided to remove that module and just use the PSU to
> > provide the 5v, with -12 and 12v supplied from external supplies.
> > Surprisingly this worked, as long as the 12v rails are up before you
> > turn on the
> > H7874 (so if you have a dead H7874 you might want to try this...).
> >
> > After some messing around with MMJ cables and various serial adapters,
> > I finally got some stuff printing to a terminal (I have abbreviated
> > this slightly because I don't want to type it out.
> >
> > ]] KA670-A V3.4, VMB 2.12
> > ]] Performing normal system tests.
> > ]] 66..65.. ... 51..
> > ]] 50..49.. ... 35..
> > ]] 34..33.. ... 19..
> > ]] 18..17.. ... 11..
> > ]]
> > ]] ?5F 2 0F 44 0000 0000 07     ; SUBTEST_5F_0D, DE_SGEC.LIS
> > ]] P1=00000000 P2=00000000 P3=00000000 P4=00000000  P5=00000000 ]]
> > P6=00000000 P7=00000000 P8=00000000 P9=0000080A P10=00000003 ]]
> > r0=00000054 r1=20084001 r2=00000000 r3=00000000  r4=00000000 ]]
> > r5=1FFFFFFC r6=C0000001 r7=00000000 r8=00004000 EPC=00000000 ]] 10..
> > ]]
> > ]] ?5C 2 06 FF 0000 0001 00     ; SUBTEST_5C_06, DE_SHAC.LIS
> > ]] P1=00000001 P2=00000000 P3=00000000 P4=00000000  P5=00000000 ]]
> > P6=00000000 P7=00000000 P8=00000000 P9=0000080A P10=00000003 ]]
> > r0=00000054 r1=0000002E r2=0000005C r3=20140784  r4=2005FFF8 ]]
> > r5=20060028 r6=20065224 r7=20004000 r8=00000000 EPC=00000000 ]]
> > 09..08..07..05..04..03..
> > ]] Normal operation not possible.
> > ]]
> > ]] >>>
> >
> > It allows me to type at this point but does not appear to do anything
> > with the input.
> >
> > I've looked through the KA670 manual and found a listing of the error
> > codes.
> >
> > 5F = SGEC (Second Generation Ethernet Controller) "loopback_type
> > no_ram_tests"
> >
> > 5C = SHAC (Single Host Adapter Chip) "shac_number"
> >
> > I'm not sure if it is relevant but I removed the TOY battery when I
> > got it to prevent it eating everything. I've not taken apart the
> > console door thing but perhaps it was too late. The SGEC might refer
> > to the ethernet controller installed on that door?
> >
> > If anyone is better at understanding these error messages I'd greatly
> > appreciate any info you could give.
> >
> > Cheers,
> > Aaron
> >
> 
> Never mind. I think these tests can be ignored, and I got rid of the SHAC
one by
> putting the terminator in the right place.
> 
> The VAX does respond to my keyboard input... when I have the terminal set
to
> the right serial config.
> 
> Need to figure out how to get it to boot from SCSI. It's picking up my
QBUS
> DHQ11 and DELQA cards fine.
> 
> I intend to replace the 12v module in the PSU with two small 12v 240v
boards
> and tap into the power coming into the PSU. This seems like a reasonable
> approach given the nature of the H7874 PSU.
> 
> Very happy the machine seems to be working!
> 
> Aaron
> 
> 
> This message and any attachment are intended solely for the addressee and
> may contain confidential information. If you have received this message in
> error, please contact the sender and delete the email and attachment.
> 
> Any views or opinions expressed by the author of this email do not
necessarily
> reflect the views of the University of Nottingham. Email communications
with
> the University of Nottingham may be monitored where permitted by law.
> 
> 
> 




More information about the cctech mailing list